Mar-2025 Latest DumpsTorrent NACE-CIP1-001 Exam Dumps with PDF and Exam Engine Free Updated Today!
Following are some new NACE-CIP1-001 Real Exam Questions!
NEW QUESTION # 36
Most industrial coatings are:
- A. Resistant to concentrated sulfuric acid
- B. Organic
- C. Resistant to temperatures above 200C
- D. Inorganic
Answer: B
NEW QUESTION # 37
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 105 Gauge Readings resulting in 35 Spot Measurements
Answer: C
NEW QUESTION # 38
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the PPE used by the Applicators
- B. Check the credentials of the Safety Officer on site
- C. Act in accordance with the site safety requirements and set an example
- D. Assume the role of the Safety Inspector
Answer: C
NEW QUESTION # 39
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Read the manufactures' instructions
- C. a), b) & c)
- D. Ensure the instrument is within calibration parameters
Answer: C
NEW QUESTION # 40
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To promote faster cure
- C. To control the evaporation rate
- D. To dissolve the resin
Answer: C
NEW QUESTION # 41
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 42
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
Answer: B
NEW QUESTION # 43
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
Answer: A
NEW QUESTION # 44
NACE SP 0178 is a standard for:
- A. Structural steel to be coated for Atmospheric Service
- B. Stainless steel pipe to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Tanks and Vessels to be Externally Coated
Answer: C
NEW QUESTION # 45
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. Treating metal with a liquid inhibiter
- C. A coating layer applied to the surface to inhibit corrosion
- D. Complete elimination pf the corrosion process
Answer: A
NEW QUESTION # 46
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Profilometer
- C. Needle pressure gauge
- D. Psychrometer
Answer: B
NEW QUESTION # 47
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Never change his/her mind
- B. Go with the majority opinion
- C. Achieve consensus through negotiation
- D. Call the supervisor
Answer: D
NEW QUESTION # 48
Which one of the following documents is the best source for coating technical data:
- A. Application Guidelines
- B. Specification
- C. Safety Data Sheet;
- D. Technical Data Sheet
Answer: D
NEW QUESTION # 49
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. A wide variety of materials
- C. Organic solvents
- D. Biodegradable detergents
Answer: B
NEW QUESTION # 50
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Bring the matter up at the pre-job conference
- B. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- C. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- D. Default to the owner's Inspection and Test Plan
Answer: A
NEW QUESTION # 51
To be of value the Inspector's documentation must be:
- A. Submitted before the end of the job
- B. Always handwritten
- C. Always typewritten
- D. Timely, accurate and concise
Answer: D
NEW QUESTION # 52
The initial steel condition is important to the NACE Inspector because:
- A. If the steel is pitted more coating will be required
- B. It affects the final appearance after blasting
- C. Less abrasive is need if the mill Scale s gone
- D. The Inspector may have to reject the Steel
Answer: D
NEW QUESTION # 53
Removal of surface contaminants is done by:
- A. Waterjetting
- B. Scarifying
- C. Abrasive blasting
- D. A combination of methods
Answer: D
NEW QUESTION # 54
Whenever dissimilar metals must join, the most common practice is to
- A. coat all connected dissimilar metals.
- B. avoid coating all connected dissimilar metals.
- C. provide cathodic protection to prevent corrosion,
- D. provide anodic protection to prevent corrosion.
Answer: A
NEW QUESTION # 55
ISO SA 2 is defined as:
- A. Light Blast Cleaning
- B. Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Very Thorough Blast Cleaning
Answer: B
NEW QUESTION # 56
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Owner's personnel
- C. All personnel involved in the job
- D. The Application personnel
Answer: C
NEW QUESTION # 57
......
Resources From:
- 2025 Latest DumpsTorrent NACE-CIP1-001 Exam Dumps (PDF & Exam Engine) Free Share: https://examsboost.dumpstorrent.com/NACE-CIP1-001-exam-prep.html
Free Resources from DumpsTorrent, We Devoted to Helping You 100% Pass All Exams!